Available in stock
StormSkin™ Spray Polyurea Materials polyurea is a very strong highly resilient super-polymer designed to aid in the protection of building infrastructures, pipelines, bridges, etc. This super-polymer is a derivative of BlastSkin™, a Military-Grade super-polymer, targeting extreme properties such as tear strength, impact and abrasion resistance. StormSkin is a non-breathable polyurea which eliminates water vapor transmission to underlying surfaces. This prevents metals to oxidize or rust under its impenetrable skin. It is used primarily to protect industrial infrastructures, waterproofing containment areas, steel frameworks, natural gas/oil pipelines, surge water walls, tanks reservoirs, rail cars, above and below ground piping, concrete and masonry waterproofing, heavy equipment coating, shipbuilding and harsh marine corrosive environments.
Engineering Technical Support Group for any technical questions regarding material, application or prospective uses.
Please call or email our Technical Support Group for any questions regarding material, application or prospective uses.
StormSkin™ is a two component 100% solids formulation which does not contain VOCs. Skin thickness has no limitation. StormSkin™ must be applied using a 2-component 1500-1800 psi high-pressure liquid pumping heated spray machine. Material and line emperatures may vary but usually initially targeted at 140°F. Thorough mixing of the B-Side component is required during application. Proper safety wear is mandatory. Surface application temperature ranges from 0°F to 150°F with surface dry. Spray cure time 2-5s. Surfaces must be prepped for cleanliness and dryness and may require the use of an adhesion promoter primer to acquire proper adhesion. Functional material operation temperature ranges from -40°F to 250°F. Final top-coat appearance is glossy and slick to the touch. This material will not flow-out or lay-down. Spray coverage at 16 mils is 100 sq. ft./ mixed gal thickness.
| Tear Strength | ASTM D624 | 500 lbs/ linear in. (8928.5 kg/m) |
| Impact | ASTM D2794 | >350 in. lbs (4.03 m-kg) |
| Tensile Strength | ASTM D412 | 3411 psi (23.52 Mpa) |
| Elongation | ASTM D412 | 450 % |
| Hardness -Shore D | ASTM D2240 | 55 |
| Abrasion -TaberCS18 | ASTM D4060 | 22 mg/1k cycles |
| Gel Time | Time | 30 s |
| Mix Ratio | PBV | 1:1 |
| Hose Heat | 160F | |
| Primary Heat | 160F | |
| Gun Pressure Minimum | 2000 PSI |
| Concrete- Primed | >300 psi | Cohesive failure; excellent bonding |
| Steel- Primed | >1000 psi | Excellent bonding |
| Composite Lamination | >250 psi | Wood failure; excellent bonding |
Preparation of substrate surface prior to the application is extremely important as durability is only as good as the weakest link in the coating system.
Concrete must be fully cured and should be prepared with a sandblasting, diamond grinding or machine sanding depending on the severity of the concrete surface condition. Similar proper preparation must be performed for metals. Primers also require this proper preparation. Always power clean using mild detergent prior to sanding, etc. Call Tech Support Group for assistance with selecting SSS application system. Also read the Application Page on this website. If patching concrete, use our mineral filled fast-set Acrylic Modified Epoxy applied by trowel. For expansion joints, use Joint Seal applied by hand cartridge dispensing gun. It is always best to perform a test within a small section of the application area prior to full scale engagement.
This technical data information is accurate to the best of our knowledge.
SuperSkinSystems™ Inc. makes no warranty, expressed or implied within the materials on this website, its use or with its any application. SuperSkinSystems™ Inc. shall not be liable for material or application related injuries,
material non-conformance, application failures or any consequential damage by the use of this product.