Available in stock
BlastSkin™ polyurea is a high strength energy absorbing super-polymer designed to deliver extensive elastomeric resiliency when subjected to explosive energy forces. This military grade formulation possess extremely high material tear strengths, exceptional abrasion and superior toughness. When subjected to an exothermic explosion, the super-polymer’s molecular geometry is pushed to a very high energy state enabling it to absorb the kinetic energy of the blast’s shock wave. It will provide containment of its underlying fractured substrate preventing the debris of shrapnel fragments. Military testing has demonstrated blast pressure rates in the order of 250 psi/ms performance at 0.25″ thickness. See BlastSkin Test Blast.
BallisticSkin™ is constructed as a NEAT super-polymer or as a composite fabrication. Material thicknesses of the super-polymers are dictated by the required level of protective performance along with application specific required substrates. Typical material substrates include very high strength steel, 6061 Aluminum, UHMW engineering polymers, fabric composites, ceramics, masonry and concrete. Please contact our technical support group for specific substrate application procedures, spray machines, safety gear and clean-up kits. Refer to MSDS for material and safety standard procedures.
BlastSkin™ is a two component 100% solids formulation which does not contain VOCs. Skin thickness has no limitation. BlastSkin™ must be applied using a 2-component high-pressure liquid pumping spray machine. Proper safety wear is mandatory. Surface application temperature ranges from 0°F to 150°F. Spray cure time 10s. Surfaces must be prepped for cleanliness and/or may require the use of an adhesion promoter primer to acquire superior adhesion. Functional operation temperature ranges from -40°F to 250°F. Final top-coat appearance is glossy smooth. Coverage at 16 mils is 100 sq. ft./ mixed gal or 9 sq.ft. at 1/4″ thickness.
| Tear Strength | ASTM D624 | >400 lbs/ linear in. (2500 Mpa) |
| Impact | ASTM D2794 | >300 in. lbs (33.89 N-m) |
| Tensile Strength | ASTM D412 | 3610 psi (25 Mpa) |
| Elongation | ASTM D412 | >350 % |
| Hardness Shore D | ASTM D2240 | 45-50 |
| Abrasion -TaberCS17 | ASTM D4060 | 25 mg/1k cycles |
| Gel Time | Time | 10 sec. |
| Mix Ratio | PBV | 1:1 |
| Hose Heat | 160F | |
| Primary Heat | 160F | |
| Gun Pressure Minimum | 2000 PSI |
| Concrete- Primed | >300 psi | Concrete cohesive failure; excellent bonding |
| Steel- Primed | >1000 psi | Excellent bonding |
| Wood- Primed | >250 psi | Wood failure; excellent bonding |
Preparation of substrate surface prior to the application is extremely important as durability is only as good as the weakest link in the coating system.
Concrete must be fully cured and should be prepared with a sandblasting, diamond grinding or machine sanding depending on the severity of the concrete surface condition. Similar proper preparation must be performed for metals. Primers also require this proper preparation. Always power clean using mild detergent prior to sanding, etc. Call TechSupport Group for assistance with selecting SSS application system. Also read the Application Page on this website. If patching concrete, use our mineral filled fast-set Acrylic Modified Epoxy applied by trowel. For expansion joints, use Joist Seal applied by hand cartridge dispensing gun. It is always best to perform a test within a small section of the application area prior to full scale engagement.
This technical data information is accurate to the best of our knowledge. SuperSkinSystems™ Inc. makes no warranty, expressed or implied within the materials on this website, its use or with its any application. SuperSkinSystems™ Inc. shall not be liable for material or application related injuries, material non-conformance, application failures or any consequential damage by the use of this product.